OWBS Outdoor Wireless Bridge System

Please Login for Pricing

The OWBS Outdoor Wireless Bridge System connects networks using an unlicensed frequency spectrum to send a strong wireless signal up to 3 miles apart. It supports VOIP, VPN, multiple MAC addresses, and DHCP across the wireless link. It is the perfect solution for connecting the networks in two or more buildings, remote video surveillance, or secure controlled access. Multiple units can be connected in a mesh configuration to allow interconnecting more than two sites.

 

Login or Sign Up

Description

The OWBS Outdoor Wireless Bridge System connects networks using an unlicensed frequency spectrum to send a strong wireless signal up to 3 miles apart with a good line of sight.

It is a high power communication, (25dBm (316mW)) operating in the 2.4GHz or 5GHz unlicensed frequency spectrum providing real-world throughput up to 100 Mb/sec. It complies with the 802.11g/n or 802.11a/n standards to insure interoperability. The OWBS creates a transparent wireless bridge between two networks up to 3 miles apart with a good line of sight. It supports VOIP, VPN, multiple MAC addresses, and DHCP across the wireless link. It is the perfect solution for connecting the networks in two or more buildings, internet access sharing, remote video surveillance or remote network access. Multiple units can be connected in a mesh configuration to allow interconnecting more than two sites.

With its password verification, MAC address authentication, SSID suppression, and advanced WPA encryption, the system provides the best available wireless data security.

Installation is a snap because of the plug-and-play features that have been built into the system. Just install the antennas and plug in the power inserters. The units will automatically find their peer and create a secure wireless network link. If changes to the pre-configured settings are desired, they can be easily done thru the built-in web interface from any point on either side of the network. There are no drivers or software that needs to be loaded to the computer.

The OWBS comes complete with all the electronics that are needed for a point to point wireless network bridge installation; including 2 powerful 14dBi 802.11g/n or 16dBi 802.11a/n MIMO antennas with built-in high power electronics, Bracket Kits that accommodate pole or wall mounting, Surge Protected Cat5e rated 24V PoE (Power Over Ethernet) power inserters and 75’ shielded outdoor rated CAT5 cable assemblies.

Data Sheet – OWBS Outdoor Wireless Bridge System

 

Features and Benefits

  • High Power Electronics and powerful antenna
    • Operation up to 3 miles with good line of sight and up to 100 Mbps real-world throughput
  • True Plug and Play
    • No driver is needed. Pre-configured at the factory for automatic peer to peer communications
  • 64 and 128bit WEP, WPA and WPA2 Encryption
    • Most powerful data security available
  • Web-based configuration
    • Remotely change device configuration or update firmware from anywhere on the network
  • Power over Ethernet
    • Antennas can be mounted up to 100meter (300’) from the power inserter
  • Layer 2 Transparent Bridge
    • Appears to network devices as if an Ethernet cable has been installed between the 2 network nodes. Passes DHCP, VOIP Packets, VLAN Packets and supports multiple MAC addresses

 

Specifications

Data Rates
2.4Ghz 802.11n: up to 300Mbps
2.4 GHz 802.11g: up to 54Mbps
5GHz 802.11n: up to 300Mbps
5GHz 802.11a: up to 54Mbps
Standards
IEEE802.11g/n, 802.11a/n, 802.3, 802.3u
Power Requirements
Power Supply: 100-240VAC 50/60Hz 12VDC to 24VDC Passive PoE
Average Power Consumption: 4W
Regulatory Certifications
FCC Part 15 / UL
RF Frequency Band
2400 ~ 2497 MHz
5100 ~ 5850 MHz
Modulation Technology
802.11n: TDMA 802.11g: OFDM 802.11a: OFDM
Receive Sensitivity (Typical)
802.11n: -90 dBm
802.11g: -75 dBm
802.11a: -75 dBm
Transmit Power
25dBm 316mW
DC Connector Power Out Input Voltage @ Max 10W
Antenna
2.4GHz 14dBi MIMO Panel Antenna, 35deg Beamwidth, >20dB front to back
5GHz 16dBi MIMO Panel Antenna, 27deg Beamwidth, >22dB front to back
Operation Mode – Bridge or Router
Point to Point Bridge, Access Point, Access Point WDS, Client, Client WDS
Interface
10/100Mbps RJ-45 LAN Port x 2
IP Configuration
Static or Auto configuration using DHCP Client
Security
MAC Address Filtering, WEP/WPA encryption, Hide SSID in beacons, Layer 2 isolation
Management Configuration
Web-based configuration (HTTP)
Console configuration (SSH)
SNMP Protocol
Firmware Upgrade
Upgrade firmware via web browser
Antenna Physical Dimensions (L x W x D)
314mm x 187mm x 65mm
12.4” x 7.3” x 2.5”
Complete System Weight: 3 kg (7 lbs )
Operating Temperature: -30°C to +70°C (-22°F to 158°F)

 

For More Information  Contact TURNSTILES.us

Additional information

Weight 10 lbs
Dimensions 12 × 12 × 9 in

You may also like…

  • PAK-QR Wiegand Wireless Portable Access Kit with QR Reader

    Please Login for Pricing
    Login or Sign Up
  • KT-2 Ethernet Ready Two-Door Controller

    Please Login for Pricing
    Login or Sign Up
  • EntraPASS KT-1 Controller

    Please Login for Pricing
    Select options
  • HID Proximity Card Readers

    Please Login for Pricing
    Select options