Description
The EntraPASS Communication Bridge Network connects networks using an unlicensed frequency spectrum to send a strong wireless signal up to 3 miles apart with a good line of sight.
The ECBN is a dual radio high power (up to 22dBm) outdoor wireless bridge system operating in the 2.4GHz AND 5GHz unlicensed frequency spectrums providing real-world throughput of up to 867 Mb/sec. The 2.4GHz radio complies with 802.3gn and the 5GHz radio complies with the 802.11ac/AN standards to insure interoperability. The ECBN creates a transparent wireless bridge between two networks up to 3 miles apart with a good line of sight and can provide a separate access point at one or both ends of the link via the 2nd radio.The bridge supports VOIP, VPN, multiple MAC addresses, and DHCP across the wireless link. It is the perfect plug-and-play solution for connecting high-speed networks in two or more buildings, internet access sharing, remote video surveillance, or remote network access. Multiple units can be connected in a mesh configuration to allow interconnecting of more than two sites. With its password verification, MAC address authentication, SSID suppression, and advanced WPA encryption, the system provides the best available wireless data security.
Installation is a snap because of the plug-and-play features that have been built into the system. Just install the antennas and plug in the power inserters. The units will automatically find their peer and create a secure wireless network link. If changes to the pre-configured settings are desired, they can be easily done thru the built-in web interface from any point on either side of the network. There are no drivers or software that need to be loaded onto the computer.
The EntraPASS Communication Bridge Network comes complete with all the electronics that are needed for a point-to-point wireless network bridge installation; including 2 powerful dual band 12dBi 802.11gn AND 14dBi 802.11ac/and 2×2 MIMO antennas with built-in high-power electronics, Bracket Kits which accommodate pole or wall mounting, Auto Ranging Gigabit rated 48V PoE (Power Over Ethernet) power inserters. Customer needs to supply CAT5 cabling between the power inserter and the antenna and between the power inserter and their computer, router, or switch.
Features and Benefits
- High Power Electronics and powerful antenna
- Operation up to 3 miles with good line of sight and up to 400 Mbps real-world throughput
- True Plug and Play
- No driver is needed. Pre-configured at the factory for automatic peer-to-peer communications
- 64 and 128bit WEP, WPA and WPA2 Encryption
- Most powerful data security available
- Web-based configuration
- Remotely change device configuration or update firmware from anywhere on the network
- Power over Ethernet
- Antennas can be mounted up to 100meter (300’) from the power inserter
- Layer 2 Transparent Bridge
- Appears to network devices as if an Ethernet cable has been installed between the 2 network nodes. Passes DHCP, VOIP Packets, VLAN Packets and supports multiple MAC addresses
Specifications
| Physical Data Rates
2.4Ghz: 400Mbps 5GHz: 867Mbps Standards IEEE802.11b/g/n, 802.11ac/an, 802.3, 802.3u, 802.3ab Power Requirements Power Supply: 100-240VAC 50/60Hz Power Over Ethernet: 803.2af/at or 48VDC Passive PoE DC Connector: 12-24VDC Average Power Consumption: 8W Regulatory Certifications FCC Part 15 / UL RF Frequency Band 2412 ~ 2472 MHz 5180 ~ 5825 MHz Modulation Technology OFDM: BPSK, QPSK,16-QAM, 64-QAM, 256- QAM Receive Sensitivity (Typical) 2.4GHz: -92 dBm 5GHz: -90 dBm Transmit Power 22dBm (158mW) Channel Width 2.4GHz: 20/40MHz 5GHz: 20/40/80/160MHz System Memory 256 MB DDR3, 128MB + 32MB Flash |
Antenna
2.4GHz 12dBi MIMO Panel Antenna, 35deg Beamwidth, >20dB front to back 5GHz 14dBi MIMO Panel Antenna, 20deg Beamwidth, >25dB front to back Operation Mode – Bridge or Router Point to Point Bridge, Access Point, Access Point WDS, Client, Client WDS, Ad-Hoc, Static WDS Interface 10/100/1000Mbps RJ-45 LAN Port x 2 IP Configuration Static or Auto configuration using DHCP Client Security MAC Address Filtering, WEP/WPA encryption, Hide SSID in beacons, Layer 2 isolation Management Configuration Web-based configuration (HTTP or HTTPS) Console configuration (SSH) Firmware Upgrade Upgrade firmware via web browser Antenna Physical Dimensions (L x W x D) 314mm x 187mm x 65mm 12.4” x 7.3” x 2.5” Complete System Weight 3.6 kg (8 lbs ) Operating Temperature -30°C to +70°C (-22°F to 158°F) Warranty: 2 Year |
